List of products by brand PrimaLuceLab

OnAxisLock 50,8mm visual back for SC telescopes with 3,3" thread is screwed directly onto the rear thread present in Celestron C11, C14 or EdgeHD 925, 1100, 1400 telescopes and lets you use all the 50.8mm diameter accessories. OnAxisLock is the accessories locking system that, compared to the one using normal screw, offers a greater clamping force,...

If you have a Celestron C8, C9.25, C11, EdgeHD 800, 925, 1100 or Meade SC and ACF 8" telescope and want to connect a Losmandy type bar under the telescope to connect it on a mount or set the same bar over to the telescope to support a parallel telescope, the best method is to fix these curved blocks that then allow you to connect the 350mm or 495mm...

0,5m Eagle power cable extension cord is used when you need a longer cable to power devices through the EAGLE.

1,0m Eagle power cable extension cord is used when you need a longer cable to power devices through the EAGLE.

The 100mm PLUS support rings are designed to be used with Ø100mm tube refractor telescope (or other telescopes brands with tube approximately 100mm in diameter) to expand the possibilities of use. In this way, for example, you can install both above and below the optical tube our PLUS plates or even guide rings. Like all the other elements of the PLUS...

The 105mm PLUS support rings are designed for acromatic and apochromatic telescope (or other telescopes brands with tube approximately 105mm diameter) to expand the possibilities of use. In this way, for example, you can install both above and below the optical tube our PLUS plates or even guide rings. Like all the other elements of the PLUS series, these...

The support rings PLUS 115mm can be used with different brands telescopes (for example refractors 120-130mm in diameter) with tube approximately 115mm in diameter. With this rings you can install both above and below the optical tube our PLUS plates or even guide rings. Compatible with telescopes by various brands, such as: Vixen VSD, Vixen AX103S, Vixen...

If you want to power EAGLE (that can power all other connected devices) and use it from a fixed station such as an observatory, you can connect it to an AC adapter power supply. This 12,8V 14A power supply (compatible with 100 to 240V) comes a 2,5 meters extension cable and EU (Schuko), UK and USA plugs. When used with the included extension, the power...

The support rings PLUS 125mm can be used with different brands telescopes (for example refractors 120-130mm in diameter) with tube approximately 125mm in diameter. With this rings you can install both above and below the optical tube our PLUS plates or even guide rings. Compatible with telescopes by various brands, such as: Takahashi FSQ106ED, Takahashi...

In order to power the Eagle (which in turn can power all other connected devices) you can use a battery or an A/C power supply. If you already have a battery of sufficient capacity, you can connect to Eagle with this 12V power cord. On the one side it has the Eagle screw connector, on the other one it has banana connector.

12V power cable with cigarette plug for Eagle - 250cm

The support rings PLUS 131mm can be used with different brands telescopes (for example refractors 100-130mm in diameter) with tube approximately 131mm in diameter. With this rings you can install both above and below the optical tube our PLUS plates or even guide rings. Compatible with telescopes by various brands, such as SkyWatcher ESPRIT 100ED. Like...

The 134mm PLUS support rings are designed telescopes with tube approximately 134mm in diameter to expand the possibilities of use. In this way, for example, you can install both above and below the optical tube our PLUS plates or even guide rings. Compatible with telescopes by various brands. Like all the other elements of the PLUS series, these rings are...

The 140mm PLUS support rings are designed telescopes with tube approximately 140mm in diameter to expand the possibilities of use. In this way, for example, you can install both above and below the optical tube our PLUS plates or even guide rings. Like all the other elements of the PLUS series, these rings are made with high mechanical precision (built...

The 145mm PLUS support rings are designed telescopes with tube approximately 145mm in diameter to expand the possibilities of use. In this way, for example, you can install both above and below the optical tube our PLUS plates or even guide rings. Like all the other elements of the PLUS series, these rings are made with high mechanical precision (built...

150mm PLUS support rings can be used with all telescopes with 150mm diameter tube to expand the possibilities of use. In this way, for example, you can install both above and below the optical tube our PLUS plates or even guide rings. Like all the other elements of the PLUS series, these rings are made with high mechanical precision (built with CNC...

155mm PLUS support rings can be used with all telescopes with 155mm diameter tube like Takahashi FS-152 and TOA-130 telescopes (or other telescopes brands with tube approximately 155mm in diameter) to expand the possibilities of use. In this way, for example, you can install both above and below the optical tube our PLUS plates or even guide rings. Like...

The 168mm PLUS support rings are designed for telescopes with tube approximately 168mm in diameter, to expand the possibilities of use. In this way, for example, you can install both above and below the optical tube our PLUS plates or even guide rings. Like all the other elements of the PLUS series, these rings are made with high mechanical precision...

The 180mm PLUS support rings can be used with telescopes that have 180mm diameter tube like Takahashi TOA150 to expand the possibilities of use. In this way, for example, you can install both above and below the optical tube our PLUS plates or even guide rings. Like all the other elements of the PLUS series, these rings are made with high mechanical...

2" nosepiece for ARCO 2" allows you to connect rotator to focusers that come with 2" visual back and to control it through SESTO SENSO 2 installed on the same focuser.

If you want to use your telescope visually with ESATTO 2" or if you want to connect a camera with a 2" nosepiece, just connect the 2" visual back for ESATTO 2" to M56 thread of the focuser draw tube. This adapter has an internal brass compression ring to avoid scratching the inserted nosepiece as well as 3 locking screws (120° separation) for a perfect...

If you want to use your telescope visually with ESATTO 3" or if you want to connect a camera with a 2" nosepiece, just connect the 2" visual back for ESATTO 3" to the M81 thread of the focuser draw tube. This adapter has an internal brass compression ring to avoid scratching the inserted nosepiece as well as 3 locking screws (120° separation) for a...

235mm PLUS support rings can be used with any brands telescopes (for example Newton 200mm in diameter) with tube approximately 235mm in diameter. With this rings you can install both above and below the optical tube our PLUS plates or even guide rings. Like all the other elements of the PLUS series, these rings are made with high mechanical precision...

PrimaLuceLab M48 extensions are available in different lengths and they present on both sides of a M48 thread (one side is male, the other is female). Completely made of metal with black anodizing (both internal and external), these extensions offer an external knurling for a better grip (very useful for example when screwing or unscrewing). Thanks to...

PrimaLuceLab T2 extensions are available in different lengths and they present on both sides of a T2 thread (one side is male, the other is female). Completely made of metal with black anodizing (both internal and external), these extensions offer an external knurling for a better grip (very useful for example when screwing or unscrewing). Thanks to...

60mm CompactGuide scope with PLUS rings is, at a really affordable price, a perfect guide scope with 60mm diameter and 240mm focal length (f/4) achromatic lens, non rotative 31,8mm helical focuser and 80mm PLUS guide rings (each with 3 screws with nylon tip) for an easy and rigid connection. Thanks to the included extension, it can also be used as a...

When installing ESATTO 3" in a telescope with a long travel focuser (such as those usually found on refractors), it is necessary to take into account the lower travel of ESATTO 3" since it's a micrometric focuser. For this reason we have designed this 65mm extension that can be installed between ESATTO 3" and the telescope tube. A precise dovetail...

PrimaLuceLab M48 extensions are available in different lengths and they present on both sides of a M48 thread (one side is male, the other is female). Completely made of metal with black anodizing (both internal and external), these extensions offer an external knurling for a better grip (very useful for example when screwing or unscrewing). Thanks to...

PrimaLuceLab T2 extensions are available in different lengths and they present on both sides of a T2 thread (one side is male, the other is female). Completely made of metal with black anodizing (both internal and external), these extensions offer an external knurling for a better grip (very useful for example when screwing or unscrewing). Thanks to...

The 80mm PLUS support rings can be used with various brands telescopes (for example refractors 60-70mm in diameter) with 80mm diameter tube. With this rings you can install both above and below the optical tube our PLUS plates or even guide rings. Like all the other elements of the PLUS series, these rings are made with high mechanical precision (built...

85mm PLUS support rings can be used with any brands telescopes (for example refractors 70mm-80mm diameter) with tube approximately 85mm in diameter. Adding these rings, you can broad the possibilities of use of this telescope as it becomes possible, for example, the installation also on other mounts or to install telescopes in parallel. Like all the other...

The 90mm PLUS support rings are designed for telescopes with tube approximately 90mm in diameter, to expand the possibilities of use. In this way, for example, you can install both above and below the optical tube our PLUS plates or even guide rings. Like all the other elements of the PLUS series, these rings are made with high mechanical precision (built...

The support rings PLUS 95mm can be used with different brands telescopes with tube approximately 95mm in diameter. With this rings you can install both above and below the optical tube our PLUS plates or even guide rings. Compatible with telescopes by various brands, such as: Takahashi FSQ85, Takahashi FS-78, Takahashi FC-100DF and DL. Like all the other...

PrimaLuceLab M48 extensions are available in different lengths and they present on both sides of a M48 thread (one side is male, the other is female). Completely made of metal with black anodizing (both internal and external), these extensions offer an external knurling for a better grip (very useful for example when screwing or unscrewing). Thanks to...

PrimaLuceLab T2 extensions are available in different lengths and they present on both sides of a T2 thread (one side is male, the other is female). Completely made of metal with black anodizing (both internal and external), these extensions offer an external knurling for a better grip (very useful for example when screwing or unscrewing). Thanks to...

This adapter allows you to connect EQ6 / AZ-EQ6 / CGEM mounts to the C82 pier for concrete base.

Adapter ESATTO 2" for ARCO 2" allows you to connect the rotator to ESATTO 2" microfocuser and control it through the special port on ESATTO. By adding this adapter to ARCO 2", thickness of rotator is 21mm.

If you are searching for the most precise motorized focuser to use the GSO/Orion/TPO Ritchey-Chretien 152mm f/9 or 203mm f/8 (both aluminum and carbon tubes) for astrophotography, this adapter allows you to connect ESATTO 2" to this telescope. You can use the standard extensions that come with the RC telescope in order to install the focuser at a precise...

If you are searching for the most precise motorized focuser to use the SkyWatcher/Orion ED80, ED100 or ED120 apochromatic refractors for astrophotography, this adapter allows you to connect ESATTO 2" to this telescope. By adding this adapter to ESATTO, your new focuser will have the same thickness of the standard one. Based on the camera and accessories...

If you are searching for the most precise motorized focuser to use the SkyWatcher/Orion Newton 200 f4 and f5 reflectors for astrophotography, this adapter allows you to connect ESATTO 2" to these telescopes. With this adapter the focuser thickness is the same of the original focuser (excluded camera adapter or visual back for ESATTO) in order to allow you...

If you are searching for the most precise motorized focuser to use the SkyWatcher/Orion Newton 250 f4 and f5 reflector for astrophotography, this adapter allows you to connect ESATTO 2" to this telescope. With this adapter the focuser thickness is the same of the original focuser (excluded camera adapter or visual back for ESATTO) in order to allow you...

If you are searching for the most precise motorized focuser for Takahashi FS-60Q, this adapter allows you to connect ESATTO 2" to this telescope. Optical thickness is 5mm. Based on the camera and accessories train you want to connect, you may need extenders to reach the focus with your camera.

Thanks to its low profile, the ESATTO 2" is the perfect motorized focuser for Takahashi telescopes with M72 thread. By adding the M72 adapter, you can thread the ESATTO 2" focuser directly onto the back of these telescopes, and use the ESATTO to achieve more precise focus. By adding the M71/M72 adapter, you can connect it also to the Takahashi Mewlon...

SC 3.3” adapter for ESATTO 2" allows you to connect the ESATTO 2" to Celestron SCT (11" and 14") and EdgeHD (925, 1100, and 1400) models. Since the ESATTO has a depth of 67mm and the 3.3” adapter has only 2mm of optical thickness, this leaves 77mm of backfocus for your camera and accessories, also when used together with the Celestron EdgeHD .7x focal...

Thanks to its low profile, the ESATTO 2" is the perfect motorized focuser for Schmidt-Cassegrain telescopes like the 8” and 9.25” Celestron SCT and EdgeHD 800 models. By adding the SC adapter, you can thread the ESATTO 2" focuser directly onto the back of these telescopes, and use the ESATTO to achieve more precise focus, avoiding focus shift and mirror...

Adapter ESATTO 3" for ARCO 2" allows you to connect the rotator to ESATTO 3" microfocuser and control it through the special port on ESATTO. By adding this adapter to ARCO 2", thickness of rotator is 21mm.

Adapter ESATTO 3" for ARCO 3" allows you to connect the rotator to ESATTO 3" microfocuser and control it through the special port on ESATTO. By adding this adapter to ARCO 3", thickness of rotator is 24.5mm.

If you are searching for the most precise motorized focuser for Borg 90FL and 107FL f3.9, this adapter allows you to connect ESATTO 3" to these telescopes. Remove the original focuser of the Borg 90FL and 107FL f3.9 and install ESATTO 3". In order to reach the focus you can use the same photo adapters that you use with the standard focuser.

If you are searching for the most precise motorized focuser to use the GSO/Orion/TPO Ritchey-Chretien 10, 12, 14 and 16 inches (both aluminum and cabron tubes) for astrophotography, this adapter allows you to connect ESATTO 3" to the M117 thread of these telescope. Optical thickness of the "PL3600236" adapter is 43mm so, when you add the ESATTO 3"...

Adapter ESATTO 3" for Meade 16 inches with 4” thread allows you to connect ESATTO 3" to Meade LX200 SCT, LX200 GPS, LX200-ACF, LX600-ACF, LX800-ACF, LX850-ACF 16 inches telescopes or to all the telescopes that have 4-inch male thread

Adapter ESATTO 3" for SkyWatcher ESPRIT 100 ED.

Adapter ESATTO 3" for SkyWatcher ESPRIT 120 ED and 150 ED

If you are searching for the most precise motorized focuser for Takahashi FSQ85, this adapter allows you to connect ESATTO 3" to this telescope. By adding the M81 to M72 adapter with stop ring you can also connect your Takahashi accessories. Based on the camera and accessories train you want to connect, you may need extenders to reach the focus with your...

Thanks to its low profile, the ESATTO 3" is the perfect motorized focuser for Takahashi telescopes with M72 thread. By adding the M72 adapter, you can thread the ESATTO 3" focuser directly onto the back of these telescopes, and use the ESATTO to achieve more precise focus.

If you are searching for the most precise motorized focuser for Takahashi TSA120, this adapter allows you to connect ESATTO 3" to this telescope. By adding the optional camera adapters with stop ring you can also connect your Takahashi accessories. Based on the camera and accessories train you want to connect, you may need extenders to reach the focus...

Adapter ESATTO 4" for ARCO 2" allows you to connect the rotator to ESATTO 4" microfocuser and control it through the special port on ESATTO. By adding this adapter to ARCO 2", thickness of rotator is 21mm.

Adapter ESATTO 4" for ARCO 3" allows you to connect the rotator to ESATTO 4" microfocuser and control it through the special port on ESATTO. By adding this adapter to ARCO 3", thickness of rotator is 24.5mm.

The adapter ESATTO 4" for Officina Stellare ProRC, RiDK, RiFAst allows you to install ESATTO 4" focuser to ProRC, RiDK, RiFAst telescopes by Officina Stellare that come with M120x1.5 female thread in the rear plate.

Adapter ESATTO 4" for Takahashi FSQ-106 allows you to install ESATTO 4" instead of the original Takahashi focuser. This adapter is designed to have, when used together with ESATTO 4", the same thickness of the original focuser in order to allow you to reach focus with the telescope. Not compatible with FSQ-106EDX 3 and 4.

Adapter ESATTO 4" for Takahashi FSQ-106EDX 3 and 4 allows you to install ESATTO 4" instead of the original Takahashi focuser. This adapter has 35mm optical thickness and it is designed to have, when used together with ESATTO 4", the same thickness of the original focuser (100.5mm) in order to allow you to reach focus with the telescope. Not compatible...

This adapter allows you to connect EQ5 / HEQ5 / AZ-EQ5 mounts to the C82 pier for concrete base.

Adapter from M110 to M68 with stop ring for ESATTO 4" allows you to connect any camera or accessory with M68 female thread. Just thread this adapter to the M110 thread of the ESATTO 4" draw tube. Thanks to the M68 stop ring for ESATTO 4" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object.

Adapter from M110 to M92 female for ESATTO 4" converts M110x1 thread of the ESATTO 4" draw tube into a M92x1 female thread that is the same of the Takahashi original focuser. This way you can connect to ESATTO 4" the Takahashi photographic adapters.

Adapter from M110 to M95 female for ESATTO 4" converts M110x1 thread of the ESATTO 4" draw tube into a M95x1 female thread. This way you can connect to ESATTO 4" the Takahashi photographic adapters.

Adapter from M110 to M98 with stop ring for ESATTO 4" allows you to connect any camera or accessory with M98 female thread. Just thread this adapter to the M110 thread of the ESATTO 4" draw tube. Thanks to the M98 stop ring for ESATTO 4" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object.

M48x0.75 adapter for ESATTO 2" allows you to connect any camera or accessory with M48x0.75 female thread. Just thread this adapter to the M56 thread of the ESATTO 2" draw tube. Thanks to the M48 stop ring for ESATTO 2" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object.

Adapter from M56 to M54 with stop ring for ESATTO 2" allows you to connect any camera or accessory with M54x0.75 female thread. Just thread this adapter to the M56 thread of the ESATTO 2" draw tube. Thanks to the M54 stop ring for ESATTO 2" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object.

Adapter from M56 to M57 with stop ring for ESATTO 2" allows you to connect any camera or accessory with M57x0.75 female thread. Just thread this adapter to the M56 thread of the ESATTO 2" focuser draw tube. Thanks to the M57 stop ring for ESATTO 2" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired...

The SC thread adapter for ESATTO 2" allows you to connect any accessory with SC female thread, like the SC focal reducers to ESATTO. Just thread this adapter to the M56 thread in the ESATTO 2" focuser draw tube. Thanks to the SC stop ring for ESATTO 2" you can also fix the camera at a precise angle in order to better frame your camera sensor at the...

Adapter from M56 to T2 with stop ring for ESATTO 2" allows you to connect any camera or accessory with T2 (M42x0.75) female thread. Just thread this adapter to the M56 thread of the ESATTO 2" draw tube. Thanks to the T2 stop ring for ESATTO 2" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object.

Adapter from M81 to M48 with stop ring for ESATTO 3" allows you to connect any camera or accessory with M48 female thread. Just thread this adapter to the M81 thread of the ESATTO 3" draw tube. Thanks to the M48 stop ring for ESATTO 3" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object.

Adapter from M81 to M54 with stop ring for ESATTO 3" allows you to connect any camera or accessory with M54 female thread. Just thread this adapter to the M81 thread of the ESATTO 3" draw tube. Thanks to the M54 stop ring for ESATTO 3" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object.

Adapter from M81 to M57 with stop ring for ESATTO 3" allows you to connect any camera or accessory with M57 female thread. Just thread this adapter to the M81 thread of the ESATTO 3" draw tube. Thanks to the M57 stop ring for ESATTO 3" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object.

Adapter from M81 to M68 female for ESATTO 3" allows you to connect any camera or accessory with M68 male thread. Just thread this adapter to the M81 thread of the ESATTO 3" draw tube.

Adapter from M81 to M68 with stop ring for ESATTO 3" allows you to connect any camera or accessory with M68 female thread. Just thread this adapter to the M81 thread of the ESATTO 3" draw tube. Thanks to the M68 stop ring for ESATTO 3" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object.

Adapter from M81 to M72 female for ESATTO 3" allows you to connect any camera or accessory with M72 male thread. Just thread this adapter to the M81 thread of the ESATTO 3" draw tube.

Adapter from M81 to M72 with stop ring for ESATTO 3" allows you to connect any camera or accessory with M72 female thread. Just thread this adapter to the M81 thread of the ESATTO 3" draw tube. Thanks to the M72 stop ring for ESATTO 3" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object.

Adapter from M81 to T2 with stop ring for ESATTO 3" allows you to connect any camera or accessory with T2 (M42x0.75) female thread. Just thread this adapter to the M81 thread of the ESATTO 3" draw tube. Thanks to the T2 stop ring for ESATTO 3" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object.

ARCO 2" is the new low profile ARC second resolution rOtator that, thanks to its incredible resolution of 1 arc second per step, is the most precise camera rotator and field de-rotator! The 2” version of ARCO has a thickness of only 20mm and a free aperture of 50.9mm. When used together with an equatorially mounted telescope, ARCO allows you to rotate the...

ARCO 3" is the larger version of our ARC second resolution rOtator that, thanks to its incredible resolution of 1 arc second per step, is the most precise camera rotator and field de-rotator! The 3” version of ARCO has a thickness of only 23mm and a free aperture of 76.3mm. When used together with an equatorially mounted telescope, ARCO allows you to...

AZ-EQ5 PLUS adapter plate

The big dovetail clamps provide the connection to telescopes support plates and are useful to create support instruments like side-by-side plates (to support two telescopes in parallel on the same mount) or to allow the precise positioning of the guide rings (to adjust precisely the weight balance), or give the possibility to assemble the Losmandy...

This black color bushing allows you to connect SESTO SENSO 2 motor shaft to focusers with 2.8mm diameter shaft. This bushing is included in the SESTO SENSO 2 box but you can also order this as spare part if needed. This red color bushing is not compatible with SESTO SENSO first generation.

This blue color bushing allows you to connect SESTO SENSO 2 motor shaft to focusers with 2.4mm diameter shaft. This bushing is included in the SESTO SENSO 2 box but you can also order this as spare part if needed. This red color bushing is not compatible with SESTO SENSO first generation.

C120 pier is the perfect solution to install even a large telescope in an astronomical observatory. The C120 pier has a high load capacity (150 kg) and, compared to a standard tripod, it provides high stability and needs for less space. A pier also prevent the telescope to touch the tripod legs during movements! This pier is available also with different...

This 1 Kg counterweight allow easier balance of the optical tubes . It can be installed both side, on the front or rear optics of any instrument. ​Dimensions: 65x60mm, 35mm thickness.

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 100mm diameter telescopes can be...

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 120mm diameter telescopes can be easily...

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 150mm diameter telescopes can be easily...

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 180mm diameter telescopes can be easily...

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 200mm diameter telescopes can be easily...

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 250mm diameter telescopes can be...

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 280mm diameter telescopes can be easily...

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 300mm diameter telescopes can be easily...

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 180mm diameter telescopes can be easily...

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 450mm diameter telescopes can be easily...

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 50mm diameter telescopes can be easily...

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 60mm diameter telescopes can be easily...

The dew heater is placed on the optical tube to prevent optics dewing. A very common problem especially in winter and in sealed optical tubes, such as refractors or Schmidt-Cassegrain. These dew heaters, 12 V powered, heat the telescope preventing the formation of condensation on the optics. This dew heater for 80mm diameter telescopes can be easily...

The dovetail clamps provide the connection to telescopes support plates and are useful to create support instruments like side-by-side plates (to support two telescopes in parallel on the same mount) or to allow the precise positioning of the guide rings (to adjust precisely the weight balance).Our dovetail clamps, unlike the common ones, offer...

DX finder base can be installed on many telescopes to let you install finder supports from many brands. The DX base provides 4 slots to allow mounting with 4 screws (not included), up to the M4, either with flat or round head. On the bottom side there is a double curvature to perfectly fit with various sizes focusers.

In order to power the Eagle (which in turn can power all other connected devices) you can use a battery or an A/C power supply. If you already have a battery of sufficient capacity, you can connect to Eagle with this 12V power cord. On the one side it has the Eagle screw connector, on the other one it has an Anderson connector with 16A fuse to...

EAGLE type connector for 3A power OUT ports allow you to it allows you to create your own cables to 12V power, through EAGLE, various instruments such as mounts, CCD cameras and other astro photography accessories. Included in the package you find instructions to proper cable heading.

EAGLE type connector for power IN and 5A or 8A power OUT ports allow you to it allows you to create your own cables to 12V power, through EAGLE, various instruments such as mounts, CCD cameras and other astro photography accessories. Included in the package you find instructions to proper cable heading.

The Eagle control unit can directly power supply accessories with power cord with cigarette plug. We build appropriate 12V power supply cables with various lengths. The Eagle-compatible power cables have on a side the jack (for 12V power supply, maximum current 3A) of the instrument they are designed for. On the other side they have the plug with screw to...

The Eagle control unit can directly power supply accessories with power cord with cigarette plug. We build appropriate 12V power supply cables with various lengths. The Eagle-compatible power cables have on a side the jack (for 12V power supply, maximum current 8A) of the instrument they are designed for. On the other side they have the plug with...

The EAGLE control unit can directly power supply Astro-Physics mounts. We build appropriate 12V power supply cables with various lengths. The EAGLE-compatible power cables have on a side the jack (for 12V power supply) of the instrument they are designed for. On the other side they have the 8A plug with screw to prevent being disconnected accidentally...

The EAGLE control unit can directly power supply Astro-Physics mounts. We build appropriate 12V power supply cables with various lengths. The EAGLE-compatible power cables have on a side the jack (for 12V power supply) of the instrument they are designed for. On the other side they have the 8A plug with screw to prevent being disconnected accidentally...

DSLR camera use lithium batteries that, during long exposure astrophotography, can run out of charge and thus avoid you imaging the night sky. That's why we created these cables with voltage regulator and false battery that allow you to power your camera directly from the Eagle (also Eagle Core) in place of the battery.

The EAGLE control unit can directly power supply FLI camera. We build appropriate 12V power supply cables with various lengths. The EAGLE-compatible power cables have on a side the jack (for 12V power supply) of the instrument they are designed for. On the other side they have the 8A plug with screw to prevent being disconnected accidentally from the EAGLE.

DSLR camera use lithium batteries that, during long exposure astrophotography, can run out of charge and thus avoid you imaging the night sky. That's why we created these cables with voltage regulator and false battery that allow you to power your camera directly from the Eagle (also Eagle Core) in place of the battery.

The EAGLE control unit can directly power supply ALUMA AC4040 and ALUMA AC 2020 cameras. We build appropriate 12V power supply cables with various lengths. The EAGLE-compatible power cables have on a side the jack (for 12V power supply) of the instrument they are designed for. On the other side they have the 8A plug with screw to prevent being...

The EAGLE control unit can directly power supply SBIG ALUMA CCD and STC CMOS cameras. We build appropriate 12V power supply cables with various lengths. The EAGLE-compatible power cables have on a side the jack (for 12V power supply) of the instrument they are designed for. On the other side they have the 8A plug with screw to prevent being disconnected...

The EAGLE control unit can directly power supply SBIG StarChaser cameras. We build appropriate 12V power supply cables with various lengths. The EAGLE-compatible power cables have on a side the jack (for 12V power supply) of the instrument they are designed for. On the other side they have the 3A plug with screw to prevent being disconnected accidentally...

The Eagle control unit can directly power supply SBIG STL and STXL camera. We build appropriate 12V power supply cables with various lengths. The Eagle-compatible power cables have on a side the jack (for 12V power supply) of the instrument they are designed for. On the other side they have the 8A plug with screw to prevent being disconnected...

The Eagle control unit can directly power supply SBIG STT and STF CCD camera. We build appropriate 12V power supply cables with various lengths. The Eagle-compatible power cables have on a side the jack (for 12V power supply) of the instrument they are designed for. On the other side they have the 8A plug with screw to prevent being disconnected...

The Eagle control unit can directly power supply SkyWatcher mounts. We build appropriate 12V power supply cables with various lengths. The Eagle-compatible power cables have on a side the jack (for 12V power supply) of the instrument they are designed for. On the other side they have the 3A plug with screw to prevent being disconnected accidentally...

The Eagle control unit can directly power supply SkyWatcher mounts. We build appropriate 12V power supply cables with various lengths. The Eagle-compatible power cables have on a side the jack (for 12V power supply) of the instrument they are designed for. On the other side they have the plug with screw to prevent being disconnected accidentally from...

The Eagle control unit can directly power supply SkyWatcher mounts. We build appropriate 12V power supply cables with various lengths. The Eagle-compatible power cables have on a side the jack (for 12V power supply) of the instrument they are designed for. On the other side they have the 8A plug with screw to prevent being disconnected accidentally...

This Eagle-compatible power cable allows you to power devices that comes with 5.5 (outer diameter) - 2.1 (inner diameter), positive tip polarity. This cable connects to the 3A port of the EAGLE, with screw connector to avoid unwanted detachment. The cable is 115cm long. By using this cable, you can power devices like SkyWatcher EQ6, HEQ5 and EQ5,...

This Eagle-compatible power cable allows you to power devices that comes with 5.5 (outer diameter) - 2.1 (inner diameter), positive tip polarity. This cable connects to the 8A port of the EAGLE, with screw connector to avoid unwanted detachment. The cable is 115cm long. By using this cable, you can power devices like QHYCCD, ATIK, ZWO, QSI cooled cameras,...

This Eagle-compatible power cable allows you to power devices that comes with 5.5 (outer diameter) - 2.5 (inner diameter), positive tip polarity. This cable connects to the 3A port of the EAGLE, with screw connector to avoid unwanted detachment. The cable is 115cm long. By using this cable, you can power devices like the ESATTO focusers and the SESTO...

This Eagle-compatible power cable allows you to power devices that comes with 5.5 (outer diameter) - 2.5 (inner diameter), positive tip polarity. This cable connects to the 8A port of the EAGLE, with screw connector to avoid unwanted detachment. The cable is 115cm long. By using this cable, you can power devices like Moravian cooled cameras.

ECCO2 is the Environmental Computerized COntroller for EAGLE that automates the management of dew heaters during long exposure astrophotography. By adding the ECCO module to your EAGLE, it will automatically and continuously monitor the temperature, humidity and pressure around your telescope and the temperature of your lenses by calculating the dew point...

This adapter allows you to install the EQ6 / EQ6-R / AZ-EQ6 mounts on the C120 pier.

EQ6, Atlas EQ-G, AZ-EQ6, Atlas Pro AZ/EQ6-G PLUS adapter plate

This adapter allows you to install the EQ8 and EQ8-R mounts on the C120 pier.

ESATTO is the new generation robotic focuser that includes motor and advanced electronics and you control with EAGLE or any Windows computer by connecting it to a USB port, or via WiFi by using the Virtual HandPad on your smartphone or tablet! The 2” version of the ESATTO 2" has 50.9mm free aperture, 15mm of draw tube travel, 5kg load capacity and...

ESATTO robotic focuser is also available in 3" version with 76.3mm free aperture, 25mm of draw tube travel, 8kg of payload capacity and an incredible resolution of 0,04 micron per step! The perfect solution for apochromatic refractors and Ritchey-Chretien or Cassegrain telescopes, and heavy imaging trains with large cameras and accessories like off axis...

ESATTO 4" is the large dimensions robotic focuser that we designed for observatory class telescopes or for astrographs that need for large free aperture, like the Takahashi FSQ-106. Compared to the smaller models, ESATTO 4" offers a larger free aperture of 102.2mm, a longer draw tube travel of 35mm and a higher payload capacity of 10 kg, always with the...

This adapter allows you to install the GM1000 mount on the C120 pier.

This adapter allows you to install the GM2000 mount on the C120 pier.

This adapter allows you to install the GM3000 mount on the C120 pier.

This GPS antenna is included with every EAGLE4, EAGLE4 S and EAGLE4 PRO. This GPS antenna is not compatible with other and/or previous versions of the EAGLE control units.

This green color bushing allows you to connect SESTO SENSO 2 motor shaft to focusers with 3.5mm diameter shaft. This bushing is included in the SESTO SENSO 2 box but you can also order this as spare part if needed. This red color bushing is not compatible with SESTO SENSO first generation.

This grey color bushing allows you to connect SESTO SENSO 2 motor shaft to focusers with 3.1mm diameter shaft. This bushing is included in the SESTO SENSO 2 box but you can also order this as spare part if needed. This red color bushing is not compatible with SESTO SENSO first generation.

If you want to install a guide telescope in parallel to the main one, guide rings offer the simplest and cheapest solution to make this. The Guide rings PLUS 115mm offer a high build quality and all the features useful for this application, allowing you to install guide telescopes such as 80mm diameter refractors. Like all the other elements of the PLUS...

If you want to install a guide telescope in parallel to the main one, guide rings offer the simplest and cheapest solution to make this. The Guide rings PLUS 80mm offer a high build quality and all the features useful for this application, allowing you to install guide telescopes such as 60mm diameter refractors. Like all the other elements of the PLUS...

ECCO is completely metal built and, for this reason, it can also be used as a finder support by adding the optional "Finder support for ECCO". So you can install your finder or guide scope above ECCO instead of using guide rings (this is a perfect solution, for example, for small apochromatic refractors and very portable setups).

HEQ5, Sirius EQ-G PLUS adapter plate

The Losmandy style dovetail plate 140mm PLUS is designed to let you install your telescopes on mounts with this plate. This dovetail plate is 140mm long and is useful for installing compact telescopes (as refractors up to 100mm in diameter) on mounts with Losmandy plate (as the SkyWatcher SkyWatcher AZ-EQ6, or EQ8). Like all the elements of the PLUS...

The Losmandy style dovetail plate 240mm PLUS is designed to let you install your telescopes on mounts with this plate. This dovetail plate is 240mm long and is useful for installing medium dimensions telescopes (such as refractors up to 130mm and reflectors up to 200mm in diameter) on mounts with Losmandy plate (as the SkyWatcher AZ-EQ6, or EQ8). Like all...

The Losmandy style dovetail plate 350mm PLUS is designed to let you install your telescopes on mounts with this plate. This dovetail plate is 350mm long and is useful for installing medium dimensions telescopes (such as refractors up to 120mm and Newton up to 250mm in diameter) on mounts with Losmandy plate (as the SkyWatcher AZ-EQ6, or EQ8). Like all the...

The Losmandy style dovetail plate 495mm PLUS is designed to let you install your telescopes on mounts with this connection. This dovetail plate is 495mm long and is useful for installing large dimensions telescopes (such as Newton up to 300mm in diameter) on mounts with Losmandy plate (as the SkyWatcher AZ-EQ6, or EQ8). Like all the elements of the PLUS...

This kit, composed of plate 495mm Losmandy style PLUS dovetail plate and PLUS curved blocks, can be installed either below (for connecting a Losmandy type dovetail bar under the telescope) and above (for supporting a parallel telescope) to the C9.25 or C11 Schmidt-Cassegrain or EdgeHD 925 and 1100 aplanatic Schmidt-Cassegrain telescopes by Celestron.

The M110 35mm extension tube can be directly threaded to the ESATTO 4" draw tube and allows you to fix camera and accessories further away from the ESATTO microfocuser. This M110 extension tube has 35mm thickness, it's made up of aluminum, black anodized and it has a M110 female on the camera side this way you can connect all the ESATTO 4" camera adapters.

M48 female to T2 male adapter allows you to connect accessories with M48 thread (48x0.75 male) to those with T2 thread (42x0,75 female). In fact sometimes the photographic accessories come with different threads: the T2 and the M48 are the most widespread and used. This adapter is made entirely of metal and has black anodizing. The adapter is very thin...

The M48 male to T2 female adapter allows you to connect accessories with M48 thread (48x0.75 female) to those with T2 thread (42x0,75 male). Sometimes in fact the photographic accessories come with different threads: the T2 and the M48 are the most widespread and used. This adapter is made entirely of metal and has black anodizing. The adapter is very...

M48 spacers are available with 0,5mm or 1mm thickness and are used together with M48 extensions in order to fine set extension total thickness.

M48 spacers are available with 0,5mm or 1mm thickness and are used together with M48 extensions in order to fine set extension total thickness.

The M48-50,8mm photographic adapter connects to all cameras and accessories with female M48x0,75 thread so you can insert camera into 50.8mm visual back. On the telescope side it has a 48mm thread to allow you to screw any 50.8mm diameter filter. Built entirely of metal and fitted with black anodizing, it has 44mm free aperture so it does not create any...

M48x0.75 female adapter for ARCO 2" allows you to connect rotator to focusers or correctors that come with M48x0.75 male thread and to control it through SESTO SENSO 2 installed on the focuser. ​PL3600424 adapter adds 6.7mm to ARCO 2” optical thickness so the total optical thickness (ARCO 2" + PL3600424) becomes 26.7mm.

The M56 15mm extension tube can be directly threaded to the ESATTO 2" draw tube and allows you to fix camera and accessories further away from the ESATTO microfocuser. This M56 extension tube has 15mm thickness, it's made up of aluminum, black anodized and it has a M56 female on the camera side this way you can connect all the ESATTO 2" camera adapters.

M63x1 adapter for ARCO 3" allows you to connect rotator to focusers or correctors that come with 63x1 female thread and to control it through SESTO SENSO 2 installed on the focuser. Optical thickness of PL3600465 adapter is 2mm.

The M81 25mm extension tube can be directly threaded to the ESATTO 3" draw tube and allows you to fix camera and accessories further away from the ESATTO microfocuser. This M81 extension tube has 25mm thickness, it's made up of aluminum, black anodized and it has a M81 female on the camera side this way you can connect all the ESATTO 3" camera adapters.

M86x1 adapter for ARCO 3" allows you to connect rotator to focusers or correctors that come with 86x1 female thread and to control it through SESTO SENSO 2 installed on the focuser.

The Maxi dovetail clamps provide the connection to telescopes support plates and are useful to create support instruments like side-by-side plates (to support two telescopes in parallel on the same mount) or to allow the precise positioning of the guide rings (to adjust precisely the weight balance), or to install it on the mounts instead of the original...

OnAxisLock 31,8mm eyepiece holder fits into 50,8mm connection like the ones of the most common focusers. OnAxisLock is the accessories locking system that, compared to those using normal screw, offers a greater clamping force, avoiding any possible flexure (so it's perfect for astrophotography), it does not damage the connected accessory and it perfectly...

OnAxisLock 50,8mm eyepiece holder for Takahashi (M72x1 thread) replaces the traditional eyepiece holder and lets you use all the 50.8mm diameter accessories. OnAxisLock is the accessories locking system that, compared to the one using normal screw, offers a greater clamping force, avoiding any possible flexure (so it's perfect for astrophotography), it...

OnAxisLock 50,8mm visual back for SC telescopes is screwed directly onto the rear thread present in most of Schmidt-Cassegrain telescopes (like the SC and EdgeHD by Celestron or Meade ones) and lets you use all the 50.8mm diameter accessories. OnAxisLock is the accessories locking system that, compared to the one using normal screw, offers a greater...

This adapter allows you to install the Paramount MX mount on the C120 pier.

When we install many instruments (for example telescope with guide scope in parallel) on the mount, it can happen that they are too close together, and that some element touches the others. That's why we created the PLUS 10mm spacers that can be fixed between two mechanical elements (such as a plate and the support rings), keeping the functionality of the...

When we install many instruments (for example telescope with guide scope in parallel) on the mount, it can happen that they are too close together, and that some element touches the others. That's why we created the PLUS 20mm spacers that can be fixed between two mechanical elements (such as a plate and the support rings), keeping the functionality of the...

When we install many instruments (for example telescope with guide scope in parallel) on the mount, it can happen that they are too close together, and that some element touches the others. That's why we created the PLUS 30mm spacers that can be fixed between two mechanical elements (such as a plate and the support rings), keeping the functionality of the...

This red color bushing allows you to connect SESTO SENSO 2 motor shaft to focusers with 2.5mm diameter shaft. This bushing is included in the SESTO SENSO 2 box but you can also order this as spare part if needed. This red color bushing is not compatible with SESTO SENSO first generation.

This 26mm adapter allows you to install SESTO SENSO 2 on focusers that come with a 26mm diameter shaft, like focusers from Explorer Scientific (or other focusers with a 26mm diameter shaft). Out of the box, SESTO SENSO 2 connects to focusers that come with a 25mm diameter shaft (the most common diameter on the market). In order to connect it to focusers...

This 33mm adapter allows you to install SESTO SENSO 2 on focusers that come with a 33mm diameter shaft, like 2,5" and 3" FeatherTouch focusers (or other focusers with a 33mm diameter shaft). Out of the box, SESTO SENSO 2 connects to focusers that come with a 25mm diameter shaft (the most common diameter on the market). In order to connect it to focusers...

This 37mm adapter allows you to install SESTO SENSO 2 on focusers that come with a 37mm diameter shaft, like 3,5" FeatherTouch and FSQ-130 (or other focusers with a 37mm diameter shaft). Out of the box, SESTO SENSO 2 connects to focusers that come with a 25mm diameter shaft (the most common diameter on the market). In order to connect it to focusers with...

SESTO SENSO 2 - The highly accurate, advanced, vibration free, robotic focusing motor for your telescope! Connect it to the USB port of your EAGLE or Windows® computer to electronically control focus while still allowing you to manually move your focuser by hand if needed. If you don’t want to focus using a computer, you can connect wirelessly from any...

T2 spacers are available with 0,5mm or 1mm thickness and are used together with T2 extensions in order to fine set extension total thickness.

T2 spacers are available with 0,5mm or 1mm thickness and are used together with T2 extensions in order to fine set extension total thickness.

The T2-50,8mm photographic adapter connects to all cameras and accessories with female T2 (M42x0,75) thread so you can insert camera into 50.8mm visual back. On the telescope side it has a 48mm thread to allow you to screw any 50.8mm diameter filter. Built entirely of metal and fitted with black anodizing, it has 39mm free aperture so it does not create...

This temperature sensor is compatible both with ECCO, the environmental computerized controller for EAGLE, and with SESTO SENSO and ESATTO, the robotic focusing solutions for telescopes. When used with ECCO, this temperature sensor allow it to record optics temperature for automatic power management of dew heaters connected to the EAGLE. When used with...

The Vixen style dovetail plate 140mm PLUS is designed to let you install telescopes or cameras on mounts with Vixen type clamp or photographic heads with Arca Swiss type clamp. This Vixen plate is 140mm long and, not only it comes with central threaded holed and slots, but also threaded holes to connect to other PLUS mechanical components such as support...

The Vixen style dovetail plate 240mm PLUS is designed to let you install telescopes or cameras on mounts with Vixen type clamp or photographic heads with Arca Swiss type clamp. This Vixen plate is 240mm long and, not only it comes with central threaded holed and slots, but also threaded holes to connect to other PLUS mechanical components such as support...

The Vixen style dovetail plate 350mm PLUS is designed to let you install telescopes or cameras on mounts with Vixen type clamp or photographic heads with Arca Swiss type clamp. This Vixen style dovetail plate is 350mm long and, not only it comes with central threaded holed and slots, but also threaded holes to connect to other PLUS mechanical components...

The Vixen style dovetail plate 90mm PLUS is designed to let you install telescopes or cameras on mounts with Vixen type clamp or photographic heads with Arca Swiss type clamp. This Vixen style dovetail plate is 90mm long and, not only it comes with central threaded holed and slots, but also threaded holes to connect to other PLUS mechanical components...

These WiFi antennas can be connected to the EAGLE control units, by using the sma connectors that are present on the EAGLE chassis. These antennas are included in the EAGLE's box and they provide 2 dBi gain. Compatible with all the EAGLE models, 2 antennas included in every set.

This yellow color bushing allows you to connect SESTO SENSO 2 motor shaft to focusers with 4.0mm diameter shaft. This bushing is included in the SESTO SENSO 2 box but you can also order this as spare part if needed. This red color bushing is not compatible with SESTO SENSO first generation.