Adapter from M60 to M54 with stop ring for ESATTO 2” LP
PL3600547
Adapter from M60 to M54 with stop ring for ESATTO 2" LP allows you to connect any camera or accessory with M54 female thread. Just thread this adapter to the M60 thread of the ESATTO 2" LP draw tube. Thanks to the M54 stop ring for ESATTO 2" LP you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object. Optical thickness is 2.5mm and, if you remove the stop ring, optical thickness is zero.
Pay in a single solution or over 3 installments of €34,15*
* Pay in 3 installments is a service offered by Paypal, if available in your state. You can select to pay in 3 installments in Paypal.
Availability:
In Stock
€102.46
VAT excluded
3
If you pay by bank transfer 99,39 €
Pay in a single solution or over 3 installments of €34,15*
* Pay in 3 installments is a service offered by Paypal, if available in your state. You can select to pay in 3 installments in Paypal.
This Eagle-compatible power cable allows you to power devices that comes with 5.5 (outer diameter) - 2.1 (inner diameter), positive tip polarity. This cable connects to the 3A port of the EAGLE, with screw connector to avoid unwanted detachment. The cable is 115cm long. By using this cable, you can power devices like SkyWatcher EQ6, HEQ5 and EQ5,...
If you have a Celestron C8, C9.25, C11, EdgeHD 800, 925, 1100 or Meade SC and ACF 8" telescope and want to connect a Losmandy type bar under the telescope to connect it on a mount or set the same bar over to the telescope to support a parallel telescope, the best method is to fix these curved blocks that then allow you to connect the 350mm or 495mm...
By adding this adapter, you can connect the ESATTO 2" LP low profile robotic focuser directly onto the back of SC telescopes. This adapter threads directly to the back SC thread of EdgeHD 8" and C8 telescopes. Optical thickness is 2.5mm.
This kit, composed of plate 350mm PLUS Losmandy style dovetail plate and PLUS curved blocks, can be installed either below (for connecting a Losmandy type dovetail bar under the telescope) and above (for supporting a parallel telescope) to the Celestron C8 or EdgeHD 800 telescopes or Meade SC and ACF 8" telescopes.
Adapter ESATTO 2” LP for telescopes with large 3.3" SC thread allows you to connect the ESATTO 2" LP to Celestron SCT (11" and 14") and EdgeHD (925, 1100, and 1400) models. Since the ESATTO 2" LP has an optical thickness of 32mm and the 3.3” adapter has only 2mm of optical thickness, this leaves 112mm of backfocus for your camera and accessories, also...
The Losmandy style dovetail plate 645mm PLUS is designed to let you install your telescopes on mounts with Losmandy style dovetail clamp. Since this dovetail plate is 645mm long and thickness is 13mm like all our Losmandy style dovetail plates, we suggest to use it with optical tubes up to 30kg in weight. This 645mm PLUS Losmandy style dovetail plate can...
Adapter from M60 to M48 with stop ring for ESATTO 2" LP allows you to connect any camera or accessory with M48 female thread. Just thread this adapter to the M60 thread of the ESATTO 2" LP draw tube. Thanks to the M48 stop ring for ESATTO 2" LP you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired...
ECCO-NTC is the adapter that allows you to use a Celestron Dew Heater Ring with the ECCO2 environmental computerized controller. Dew Heater Rings differ from standard dew heater straps, as they utilize an NTC thermistor to measure temperature of SC or aplanatic SC telescopes corrector plate without the need for an external temperature probe.
ECCO-NTC is...
SESTO SENSO 2 - The highly accurate, advanced, vibration free, robotic focusing motor for your telescope! Connect it to the USB port of your EAGLE or Windows® computer to electronically control focus while still allowing you to manually move your focuser by hand if needed. If you don’t want to focus using a computer, you can connect wirelessly from any...
This temperature sensor is compatible both with ECCO, the environmental computerized controller for EAGLE, and with SESTO SENSO and ESATTO, the robotic focusing solutions for telescopes. When used with ECCO, this temperature sensor allow it to record optics temperature for automatic power management of dew heaters connected to the EAGLE. When used with...
PLAY is the astrophotography software that allows you to record beautiful pictures of the night sky in the simplest way, with the telescope, mount and camera you prefer! Connect all your telescope devices to PLAY and start your exploration of the Universe: check the Planetarium sky chart to find astrophotography targets, visualise your field of view, and...
This bundle includes the ESATTO 2" LP low profile focuser, the ARCO 2" rotator and the adapter to connect them, allowing you to take remote control of focusing and rotation in a compact focuser with just 54.2mm of thickness and 50.9mm of free aperture.
By adding this adapter, you can connect the ESATTO 2" LP low profile robotic focuser directly onto the back of SC telescopes. This adapter threads directly to the back SC thread of EdgeHD 8" and C8 telescopes. Optical thickness is 2.5mm.
ESATTO 2” LP is the most compact low profile robotic focuser specially designed for telescopes with low backfocus and it can fit also the Celestron EdgeHD 8"! At just 32mm of thickness, ESATTO 2” LP provides a large 50.9mm free aperture with 10mm of travel, 5 kg of payload capacity and an incredible resolution of 0.03 microns per step! And like all the...
EAGLE6 is the most advanced all-in-one computer for telescopes and astrophotography, combining powerful new features to simplify remote control and power management while allowing you to use astronomy devices and Windows softwares of your choice. Housed in the innovative PLUS aluminum body designed for easy telescope installation and cable management,...