Technical support:
+39 0434 1696106 (Mon-Fri) or email!
0item(s)

You have no items in your shopping cart.

Technical support:
+39 0434 1696106 (Mon-Fri) or email!

Product was successfully added to your shopping cart.
  • WEB230-5 2.3 meter prime focus parabolic antenna with supports WEB230-5 2.3 meter prime focus parabolic antenna with supports

Free shipping in most EU countries

for order at least €250

WEB230-5 2.3 meter prime focus parabolic antenna with supports

Product code: WEB230-5

Be the first to review this product

Quick Overview

Radio telescopes capture radio signal coming from space which are, in many cases, very weak. This is why radio astronomers use very large diameter parabolic antennas, even more than 50 meters in diameter. How can an amateur own and operate a parabolic antenna that is powerful, compact, lightweight and yet not too expensive? The WEB230-5 2.3 meter prime focus parabolic antenna with supports is the ideal solution to install a parabolic antenna on an equatorial mount (with Losmandy dovetail clamp and with a load capacity of at least 50 Kg) to capture radio waves. The dovetail bar is the same as used by many telescopes, so you can use it just like a normal optical tube. WEB230-5 2.3 meter prime focus parabolic antenna with supports can be installed on many different mounts.

Availability: In stock

Details

Receiving radio waves from space is a difficult task that requires the use of instruments specially designed for the radio astronomer: so we designed the WEB230-5 2.3 meter prime focus parabolic antenna with supports. It was specifically designed to create an amateur radio telescope with a German equatorial mount, just like the ones used for normal optical telescopes.

 

 

WEB230-5 2.3 meter prime focus parabolic antenna with supports

 

 

Large 2,3 meter diameter parabolic antenna

Radio astronomy studies signals that, in most cases, are very weak. So when you are studying frequencies higher than 1 GHz, it is necessary to use a parabolic antenna with a diameter as large as possible. The WEB230-5 2.3 meter prime focus parabolic antenna with supports features a large diameter so it has high gain and resolution. In this way you can capture weaker radio signals and separate finer details.

Mesh construction - incredibly light

In order to allow installation and proper operation of a parabolic antenna on a not-too-expensive equatorial mount (like the EQ8), the main reflector must weigh no more than 12 kg, while the total weight of the antenna (with counterweights and supports) must not exceed 50 kg. The main reflector of the WEB230-5 antenna weighs only 10 kg so you can install it on an equatorial mount with a load capacity of at least 50 kg (with Losmandy dovetail). The perforated surface also results in a low reflection of visible and infrared waves (ie, when the radio telescope points at the Sun, the illuminator and the LNA do not heat up too much) and a lower wind effect. The reflecting surface of this parabolic antenna (primary reflector) is composed of an aluminum mesh with 3x4mm square mesh size for optimum reflectivity of radio waves with frequencies up to 5 GHz. 

 

 

 

 

Support for L-band feed and focus system

In order to study the weak radio astronomical signals, it is necessary to optimize the antenna by adjusting precisely also the focus point. For this reason 4 aluminum rods rigidly maintain feed and LNA support (feed and LNA are not included in the WEB230-5 price). An appropriately-sized inner sleeve allows you to fine tune the focus of the system in order to maximize the gain. A special box insulates the LNA to minimize gain variations.

Support device for equatorial mounts

Our support device for equatorial mounts (patented) allows you to install the WEB230-5 2.3 meter prime focus parabolic antenna with supports on any equatorial mount (with Losmandy dovetail and load capacity of at least 50 kg, eg. EQ8 type). Thanks to a sliding system with two counterweights and protection against accidental blows, you can obtain perfect balance even in the declination axis for maximum tracking and automatic GOTO performances of the mount. Without counterweights the radio telescope would be completely biased towards the front (because of the weight of the primary reflector and LNA + illuminator group with support rods) and therefore could not properly point and track objects in the sky. A special system of rear tie rods increases the rigidity of the structure while minimizing the deformation of such a large-diameter parabolic antenna.

Technical Specifications

Antenna diameter (m) 2,3
Material Aluminium
Antenna type Prime focus
Plate Losmandy
Reflector material Mesh
Working frequency (GHz) 1 - 5
Counterweights 2 x 5 Kg
Front support shafts number 4
Rear shaft number 3
L band illuminator support Yes

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

  1. Be the first to review this product

Write Your Own Review

How do you rate this product? *

  1 star 2 stars 3 stars 4 stars 5 stars
Vote