You have no items in your shopping cart.
The QSI 600 Series offers dual read rates of up to 8 MHz with high-speed USB 2.0 and full 16-bit output that allow 600 Series cameras to produce high quality images with high frame rates, extremely wide dynamic range, excellent linearity and exceptionally low noise. The QSI 600 Series has many different models and a variety of options and accessories are available to meet your specific medical, astronomical or industrial imaging objectives. The superb imaging performance of 600 Series cameras is wrapped in an attractive, compact design with outstanding power efficiency and investment protecting upgradeability. The refined engineering and impressive fit, finish and attention to detail will surpass your highest expectations.
8.3 megapixel Kodak KAF-8300 sensor
Integrated filter wheel for 5x31,8mm filters
5.4µm pixel provides high resolution
High Speed USB 2.0 and read rates up to 8 MHz
2-Stage TEC w/ cooling to 45°C below ambient
Broad Software support
ASCOM-compatible Windows COM API
Linux drivers and API
The large 3326x2504 sensor in the QSI 683 provides unprecedented field of view in a camera using standard 1¼" filters. The KAF-8300 sensor has excellent quantum efficiency between 350nm and 1000nm with peak QE over 60%. Low dark current and high pixel charge capacity result in a dynamic range exceeding 70db. Micro lenses cover the surface of the CCD to focus the light through the transparent gate to further increase optical response.
The 683s camera incorporates QSI's proprietary internal, even-illumination mechanical shutter in the 'mid-size' camera body configuration. The shutter is not only used for timing exposures, but can be left closed to produce 'dark frames' for subsequent image processing. Exposures can be as short as 0.03 seconds or as long as 240 minutes. The shutter is rated for more than 1 million cycles.
All QSI 600 Series cameras utilize High Speed USB 2.0 port (USB 1.1 compatible) for connection to the host computer and imaging application software. Read and transfer time for an entire 8.3mp image frame is typically approximately one second in High Speed mode and less than 12 seconds in High Quality mode. The frame rate can be further increased by reading just a portion of the image (ROI) or with flexible on-chip binning. A four channel optically isolated control port is accessible through a standard 6 pin modular connector. The signal pin-out is compatible with most modern telescope mount drive correctors and is intended to be used for telescope guiding.
Two separate analog processing chains, providing dual read rates, allow the QSI 600 Series to meet two seemingly incompatible imaging goals. The QSI 600 Series High Quality mode provides the highest possible Signal to Noise Ratio (SNR) for applications that require the lowest noise and widest possible dynamic range. High Speed mode has a read rate of 8MHz providing high speed reads at multiple frames per second. The read mode is easily changed under program control providing exceptional flexibility it tuning the camera's performance to the desired imaging goals.
Small enough to practically hide behind a CD-ROM, the medium format QSI 600 Series family sets new standards for full-featured, high performance scientific CCD cameras. The striking appearance, refined design and superior fit and finish only hint at the advanced technical performance lurking inside. Some have described it as a work of art.
Key in the compact design of the 600 Series cameras is a very efficient custom 2-stage thermoelectric cooler (TEC) subsystem. Intelligent, programmable cooling fans are integrated into the rear of the camera body to remove the heat generated by the cooler. Typically, forced air cooling lowers the regulated CCD temperature by up to 45°C below ambient utilizing 85% power. Tight +/- 0.1°C temperature regulation is maintained at temperature settings of 10°C below ambient and lower. A slim liquid heat exchanger can be attached to the rear of the camera body to increase the cooling further, up to 55°C below the temperature of the circulating fluid.
|Type:||Camera CCD raffreddata|
|Sensor dimensions (mm)||17.96mm x 13.52mm|
|Sensor diagonal (mm)||22.6|
|Pixels dimensions (µm)||5.4µm x 5.4µm|
|A/D converter||16 bit|
|Cooling||-45°C rispetto a T ambientale|
|Readout Noise (e-)||8 electrons RMS|
|ST4 integrated autoguide port||No|
|Telescope interface||Filetto T femmina (42x0,75)|
|Connection to PC||USB 2.0|
|Power||External 12V 2A|
|Weight (gr.)||1130 gr.|